OX mounting instructions Parts needed to mount the OX extrusion xtrusion Mounting strip () xtrusion () nd aps () Power supply bracket () Spacers () land () Plastic rod dia. 2.4 mm () Plastic rod dia. 4 mm () Pressure screws M5 () Pressure screws M3 () onductive fastener (K) Threaded rod dia. 3mm (L) Tools needed for mounting: - drill - screwdriver - screws - hand saw - llen wrenches (dia. 3 mm, dia. 5 mm) NOT! ll L strips must be connected to a 12 V or 24 V power supply. MPORTNT: The manual presents the simplest mounting procedure. More mounting procedures and related accessories can be found at klusdesign.eu www.klusesign.eu 1
OX mounting instructions 1. rill screw holes in the mounting strip () (min. two) and holes for cable glands. 2. Put on the cable gland () and the spacers () on the drilled holes. 3. ix the mounting strip () to the surface with screws suitable for the surface material. Run the cable out through the gland. 4. ttach the selected power supply bracket (). 5. rill holes in the extrusion () to install the conductive fasteners. 6. nsert the power supply bracket and the power supply () into the extrusion (). www.klusesign.eu 2
OX mounting instructions 7. Secure the bracket () with the power supply by inserting one plastic rod dia. 2.4 mm () into the guides on each side. ut the rods to the required length. Then secure the rods with M3 pressure screws () tightening them with the llen wrench. 8. Mount the conductive fasteners (K) in the drilled holes and connect power (one pole to each conductive fastener). ownload the conductive fastener manual at klusdesign.eu K 9. Mount the threaded rod (L). 10. Snap the extrusion () onto the mounting strip () and connect power. L 11. Secure the extrusion () against falling off by inserting the plastic rods dia. 4 mm () into the guides and tightening them with the M5 pressure screws (). using the llen wrench. Sink the pressure screws adequately so that there is room for end caps. 12. Put on the end caps. www.klusesign.eu 3
Montaż oprawy na bazie profilu OX zęści niezbędne do skonstruowania oprawy na bazie profilu OX Listwa montażowa () Profil () Zaślepki () Podkładka pod zasilacz () Podkładki dystansowe () ławnica () Pręt tworzywowy i 2,4 mm () Pręt tworzywowy i 4 mm () ociski M5 () ociski M3 () Zawieszka zasilająca (K) wintowany pręt i 3mm (L) lementy niezbędne przy czynnościach montażowych: - wiertarka - wkrętarka / śrubokręt - wkręty - ręczna piła - klucze imbusowe (i 3 mm, i 5 mm) UW! Wszystkie taśmy L powinny być podłączone do zasilacza 12 V lub 24 V. WŻN: nstrukcja przedstawia najbardziej podstawową formę montażu. Więcej metod i powiązanych akcesoriów znajdziesz na stronie klusdesign.pl www.klusesign.pl 1
Montaż oprawy na bazie profilu OX 1. Wywierć w listwie montażowej () otwory na wkręty (minimum dwa) oraz otwory na dławnice. 2. Załóż dławnicę () oraz podkładki dystansowe () przy otworach na wkręty. 3. Przykręć listwę montażową () do powierzchni. Wyprowadż przewód przez dławnicę. Użyj wkrętów odpowiednich do danego materiału. 4. Wybrany zasilacz przymocuj do podkładki (). 5. Nawierć profil () tak by można było zainstalować zawieszki zasilające. 6. Wsuń podkładkę z zasilaczem () w profil (). www.klusesign.pl 2
Montaż oprawy na bazie profilu OX 7. Zabezpiecz podkładkę () z zasilaczem, wsuwając w prowadnice po jednym pręcie tworzywowym i 2,4 mm () z każdej strony. Pręty należy dociąć do odpowiedniej długości. Nastepnie zabezpiecz pręty dociskami M3 (), dokręcając je kluczem imbusowym. 8. Zainstaluj zawieszki zasilające (K) w wywierconych otworach i podłącz zasilanie (jeden biegun do pojedyńczej zawieszki). Pobierz instrukcję zawieszki ze strony klusdesign.pl K 9. Zainstaluj gwintowany pręt (L). 10. Wepnij profil () do listwy montażowej () i podłącz zasilanie. L 11. Zabezpiecz profil () przed wypadnięciem wsuwając w prowadnice pręty tworzywowe i 4 mm () i dokręcając je dociskami M5 (). Użyj klucza imbusowego. ociski wkręć na tyle głeboko by pozostawić miejsce na zaślepki. 12. Załóż zaślepki www.klusesign.pl 3