LISTA CZĘŚCI (PARTS LIST) NR CZĘŚCI (PART NO.) ILOŚĆ (QUANTITY) OPIS (DESCRIPTION) 1 ŚRUBA (HEX BOLT) x70 6 ŚRUBA (HEX BOLT) 0 3 ŚRUBA (CARRIAGE BOLT) 5 INSTRUKCJA MONTAŻU (ASSEMBLY INSTRUCTION) MH-W10 4 3 ŚRUBA (HEX BOLT) 0 5 ZAŚLEPKA (END CAP) Ø5 6 ZAŚL. GUM. (RUBBER) 50x30 7 ZAŚLEPKA (END CAP) 400 8 4 WKRĘT (SCREW) Ø4x 9 ŁĄCZNIK RAMY (SUPPORT) 10 TULEJKA (BUSHING) Ø16x10 6 TULEJKA (BUSHING) Ø16 1 1 TAP. SIEDZISKA (SEAT UPHOLSTERY) 13 1 SUWADŁO (DISC POST) 15 3 ROLKA (WHEEL) Ø0 16 1 RAMA (FRAME) PRZELOTKA (REDUCER) 18 1 STOPA (FOOT) 19 1 RAMA WYCIĄGU (MAIN FRAME) 19 PODKŁADKA (WASHER) 1 6 OSŁONA (COVER) GUMA (RUBBER) Ø40/Øx8 19 NAKŁ. NA ŚR. (END CAP) 10 NAKRĘTKA (NUT) 5 3 NAKR. SAMOZAB. (LOCKNUT) 6 LINKA (CABLE) L=1870 mm 7 KULA GUM. (RUBBER) 8 KIESZEŃ (WHEEL SUPPORT) 9 1 KIESZEŃ (WHEEL SUPPORT) 30 1 DRĄŻEK (LAT BAR) 31 1 BLOKADA STÓP (PLATFORM) 3 RĄCZKA GUM. (HAND GRIP) 4 KARABIŃCZYK (SNAP HOOK) 34 8 ZACISK LINKI (WIRE ROPE CLIP) Strona / Page 1 MARBO E SPORT P R O F E S S I O N A L F I T N E S S E Q U I P M E N T www.marbo-sport.pl
PRZED MONTAŻEM Przeczytaj to zanim rozpoczniesz montaż urządzenia Podczas montażu, podążaj zgodnie z instrukcją Montaż rozpocznij od pierwszego kroku kończąc na ostatnim. Instrukcja montażu podzielona jest na etapy (kroki), wykonuj jeden etap na raz, dopiero po jego ukończeniu, przejdź do następnego kroku. Jeśli podczas montażu zorientujesz się, że brakuje którejś części, poinformuj nas o tym podając jej numer. Aby ułatwić montaż, zastosowaliśmy w instrukcji linie montażowe. Urządzenie musi być sprawdzane co najmniej raz w tygodniu pod względem poziomu dokręcenia śrub, nakrętek i elementów tapicerowanych które mogą sie luzować podczas użytkowania urządzenia, a także pod względem zużycia elementów obrotowych BEFORE ASSEMBLY This must be read before you start assembling this unit. You must follow the assembly instructions exactly as outlined. Assemble this unit starting at the beginning and work to the end The assembly instructions are set out so that you are only doing one section at a time, therefore you will finish one section and move on to the next. If something is missing when assembling this unit, you must notify us of the part number of the exact nut, bolt of part that is missing. To help you assemble this unit we have used line drawings. Check the line drawings for the exact positioning of the parts. The unit will need to be checked at least once a week for nuts and bolts that can work loose, upholstered pieces working loose and wear on pivot assemblies. POTRZEBNE NARZĘDZIA / TOOLS NEEDED KLUCZ NASADOWY (SOCKET WRENCH) x KLUCZ PŁASKO-OCZKOWY (KEY FLAT EYE) 1x8 MŁOTEK GUMOWY (RUBBER HAMMER) ŚRUBOKRĘT (SCREWDRIVER) Strona / Page Strona / Page
KROK (STEP) 1 7 Zaślepka 400 x1 7 5 19 Zaślepka Ø5 Guma (Rubber) Ø40/Øx8 Przelotka (Reducer) 5 13 5 7 Strona / Page 10 Strona / Page 3
Nakł. na śr. 10 KROK (STEP) Zaśl. gum. (Rubber) 0x30 6 (Carriage bolt) 105 Nakrętka (Nut) Ø10 16 6 18 3 3 6 3 31 Strona / Page 4 40mm MIN 70mm KROK (STEP) 7 3 30 Na wolny koniec linki nasunąć KULĘ GUM. (7) 3 On the free end of rope put the RUBBER (7) Wyciąg górny Linka nr 1 (1870mm) 6 Linka nr (1870mm) 7 Wyciąg dolny Karabińczyk (Snap hook) Zacisk linki (Wire rope clip) 7 34 Strona / Page 9 34
KROK (STEP) 6 Kula gum. (Rubber) 7 KROK (STEP) 3 9 x1 9 7 19 0 7 15 6 Nakrętka (Nut) 9 Ø10 x7 14 Nakł. na śr. x7 16 Strona / Page 8 Strona / Page 5
KROK (STEP) 4 8 10 1 1 8 8 10 x70 0 Nakrętka (Nut) Tulejka (Bushing) Ø16x10 Ø10 Wkręt (Screw) Ø4x Nakł. na śr. 1 1 10 8 Strona / Page 6 KROK (STEP) 5 1 5 1 8 4 9 15 15 8 4 1 0 x3 Tulejka (Bushing) Ø16 Nakr. samozab. (Locknut) x3 Rolka (Wheel) Ø0 x3 Osłona (Cover) Nakł. na śr. 5 1 4 5 15 1 Strona / Page 7